- Refresh button: real handler — calls the new mesh.refresh (radio
re-query) plus contacts/federation/outbox re-reads, disabled with a
spinner while running (was an unawaited cache repaint with no feedback
that skipped half the list's data sources).
- Broadcast button: success ('Sent ✓') and failure states with the error
in the tooltip; failures no longer vanish as unhandled rejections.
- The store's 5s status poll no longer wipes the error banner each tick.
- Contacts/aliases, federation nodes and the outbox badge refresh every
~30s (were mount-only and went permanently stale).
- Peer-list empty state keys on the merged list, so federation rows and
the channel rows still render with no radio attached.
- Device setup modal: 'Set Recommended' naming, probe progress bar with
stage labels instead of an anonymous spinner.
- Device panel: name save clears properly (empty = fall back to server
name) and the confirmation reflects the new live apply.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
The RF section shipped as four bare fields; restore a prepopulated plan
list (dropdown) with Custom unlocking free entry, per operator direction.
Preset labels carry the full values, so the number fields render only in
Custom mode — no duplicated display. Presets limited to verifiable
sources: the repo's MeshCore community plans (EU 868/433), the MeshCore
firmware's own build defaults (platformio.ini arduino_base 869.618/62.5/
SF8 CR5; companion example 915.0/250/SF10/CR5), and the operator-attested
Portugal plan (869.618/62.5/SF8/CR8). Stored params are matched back to a
named preset on load; hand-editing flips the dropdown to Custom.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Device panel gets MeshCore RF fields (frequency MHz, bandwidth kHz, SF, CR)
wired to mesh.configure's validated lora_radio_params; shown only for
MeshCore radios, all-empty leaves the radio's flashed settings untouched.
Human units in the UI, firmware field units on the wire. Per operator
direction the panel's static stat rows duplicating editable fields (name,
region, channel) are dropped — the editable control is the display. Stale
'adjust via a MeshCore client' hints updated: the node programs the radio now.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Plugging in a LoRa radio now pops a global two-step setup modal on any
page: step 1 shows the ACTUAL detected board (25 board SVGs vendored
from the Meshtastic web-flasher, GPL-3.0; matched by USB product string
on native-USB boards, vid:pid heuristics for bridge chips, animated
fallback otherwise); step 2 configures with Archipelago presets — the
LoRa region pre-selected from the node's location (new lat/lon→region
mapping), channel 'archipelago', node name, and an advanced firmware
pin. Options adapt per protocol: region+channel program Meshtastic;
MeshCore shows its community frequency plan (firmware owns RF); RNode
defers to the Reticulum daemon config.
Backend: mesh.configure now accepts lora_region (validated against the
driver's region table) and device_kind (probe pin); mesh.status returns
the persisted values plus per-port USB identity (sysfs vid/pid/product)
for board identification. The Mesh Device tab gains a full settings
form (region with duty-cycle/legality hints, firmware pin, channel,
name, identity broadcast) replacing the read-only panel; the old
Mesh-page-only onboarding modal is superseded by the global flow.
Mock backend: stateful mesh config so the dev UI demos the full
detect→configure round-trip (disable mesh → modal fires with Heltec V3).
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
New MeshDevicePanel.vue, added as a 4th/5th tab entry to activeTab/toolsTab/
mobileTab following the exact existing pattern (chat/bitcoin/deadman/
assistant/map). Shows firmware version, node ID, advert name, LoRa region,
channel, and device type -- firmware_version/self_node_id were already
server-side but never rendered; region is new (composed into MeshStatus from
MeshConfig.lora_region at read time, not part of the live session state).
Reboot button wired to the already-working mesh.reboot-radio RPC.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
