The step-3 template's condition for showing the picker vs. the progress/
result view was `!flashJob?.active && flashJob?.stage !== 'done'`. That's
true for "no job started yet" (flashJob is null) — but ALSO true for a job
that just FAILED (active:false, stage:'failed'), since 'failed' !== 'done'.
So a failed flash silently reverted to the family/board picker instead of
showing the failure state (error message + log tail) — reported live as
"it went to the download screen and then back to the flash screen" with no
visible error.
Now shows the picker only when no job has been started yet (`!flashJob`);
once a job exists, the progress/result view is always shown, whether it's
still running, succeeded, or failed — the existing error/log-tail markup in
that view already handles all three, it just wasn't being reached.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
The "couldn't confirm the board automatically" warning was checking the
display label text (/v3/i, /v4/i) instead of the same vid:pid table the
backend actually uses to resolve the board. A Heltec V3's CP2102 bridge
chip reports "CP2102 USB to UART Bridge Controller" in its USB strings, not
"Heltec", so meshDeviceImages.ts's fallback label ("LoRa radio (CP2102
serial)") never matched the regex — showing the low-confidence warning (and
leaving the board picker empty) even though the backend's
resolve_flash_board can safely auto-detect V3 via vid:pid 10c4:ea60.
Now checks the same vid:pid directly from detected_device_info, matching
mesh::flash::resolve_flash_board exactly. V4 still has no auto-match entry,
same as the backend — its vid:pid (303a:1001) is the ESP32-S3's generic
native-USB descriptor, not V4-specific, so manual selection is still
required there.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Plugging in any LoRa radio now surfaces the device setup modal EVERY time
(dismissals clear on unplug; works while mesh is enabled; 2-poll debounce
so ordinary reconnect blips don't flash it), showing what's currently on
the stick before anything is written:
- mesh.probe-device RPC: identifies the firmware read-only in the same
Reticulum->Meshcore->Meshtastic order as auto-detect. Meshtastic yields
region/modem-preset/channels (want_config is a read); MeshCore yields
name/node-id + firmware version via the previously-unused
CMD_DEVICE_QUERY; RNode via the bare KISS DETECT (no daemon spawn).
Path must be a detected candidate port; the live session's port refuses.
- "Keep As Is": manage_radio=false persists in MeshConfig and the session
skips every on-connect config write (region, channel, PHY params, advert
name) — the radio runs exactly as flashed, hot-swappable.
- "Set Up with Archipelago Settings": second screen shows the params that
will be applied (channel, region, the node's persisted RF params - e.g.
the validated Portugal preset - with the per-region community plan as
fallback) before writing anything.
- Stale-type fix: disconnect now resets device_type/firmware_version, so
a swapped stick no longer shows the previous radio's firmware; probed
kind pins device_kind so the right probe runs first on connect.
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
Plugging in a LoRa radio now pops a global two-step setup modal on any
page: step 1 shows the ACTUAL detected board (25 board SVGs vendored
from the Meshtastic web-flasher, GPL-3.0; matched by USB product string
on native-USB boards, vid:pid heuristics for bridge chips, animated
fallback otherwise); step 2 configures with Archipelago presets — the
LoRa region pre-selected from the node's location (new lat/lon→region
mapping), channel 'archipelago', node name, and an advanced firmware
pin. Options adapt per protocol: region+channel program Meshtastic;
MeshCore shows its community frequency plan (firmware owns RF); RNode
defers to the Reticulum daemon config.
Backend: mesh.configure now accepts lora_region (validated against the
driver's region table) and device_kind (probe pin); mesh.status returns
the persisted values plus per-port USB identity (sysfs vid/pid/product)
for board identification. The Mesh Device tab gains a full settings
form (region with duty-cycle/legality hints, firmware pin, channel,
name, identity broadcast) replacing the read-only panel; the old
Mesh-page-only onboarding modal is superseded by the global flow.
Mock backend: stateful mesh config so the dev UI demos the full
detect→configure round-trip (disable mesh → modal fires with Heltec V3).
Co-Authored-By: Claude Fable 5 <noreply@anthropic.com>
